WILO Wilo Smart-Pump Stratos MAXO 50/0.5-12 PN6/10 (DE) – 2186205

Premium Smart Pump Wilo-Stratos MAXO High-efficiency inline wet rotor pump with EC motor and electronic power adjustment. Can be used for heating water, cold water, and water-glycol mixtures. Energy efficiency index (EEI) between ≤ 0.17 and ≤ 0.19 depending on the pump type. Control modes: Permanent, automatic power adjustment to the system requirements without setpoint specification Wilo-Dynamic Adapt plus (factory setting). Up to 20% energy savings compared to the dp-v control mode. Constant temperature (T-const.) Constant differential temperature (dT-const.) Demand-driven volume flow optimization of the booster pump through networking and communication with multiple pumps (Multi-Flow Adaptation). Constant volume flow (Q-const.) Differential pressure control dp-c at a remote point in the pipe network (critical point control) Constant differential pressure (dp-c) Variable differential pressure (dp-v) with the option of nominal operating point input Constant speed (n-const.) User-defined PID control Functions: Heat quantity acquisition Cold quantity acquisition Automatic shutdown of the pump when zero flow is detected (No-Flow Stop) Switching between heating and cooling mode (automatic, external or manual) Adjustable volume flow limitation by Q-Limit function (Qmin. and Qmax.) Double pump operating modes: Efficiency-optimized addition operation for dp-c and dp-v, main/standby operation Save and restore configured pump settings (3 restore points) Fault/warning message display in plain text including recommended remedies Ventilation function for automatic venting of the rotor chamber Automatic night setback Automatic deblocking function and integrated motor full protection Dry run detection Display: Control mode Setpoint Volume flow Temperature Power consumption Electrical consumption Active influences (e.g. STOP, No-Flow Stop) Design: 2 configurable analog inputs: 0-10 V, 2-10 V, 0-20 mA, 4-20 mA and commercially available Pt1000; power supply with +24 V DC 2 configurable digital inputs (Ext. OFF, Ext. Min, Ext. Max, Heating/Cooling, Manual Override (BMS decoupled), Operating Lock (Keypad lock and remote control configuration protection)) 2 configurable signal relays for operating and fault messages Slot for Wilo-CIF modules with interfaces for building automation BA (Optional accessories: CIF modules Modbus RTU, Modbus TCP, BACnet MS/TP, BACnet IP, LON, PLR, CANopen) Wilo Net as Wilo system bus for communication between Wilo products, e.g. Multi-Flow Adaptation; double pump operation and Wilo-Smart Gateway Integrated temperature sensor Automatic emergency operation in special conditions (pump speed definable) e.g. in case of bus communication or sensor value failure Graphic color display (4.3 inches) with one-button manual control Read out and set operating data and, for example, create a commissioning report via Bluetooth interface (without additional accessories) using the Wilo Assistant App Double pump management integrated (double pumps are pre-wired), when using 2 single pumps as a double pump unit, connection via WILO Net Cable break detection for analog signal (in conjunction with 2-10 V or 4-20 mA) Outdoor installation with weather protection possible according to installation and operating instructions Date and time preset Thermal insulation shell for heating applications 5-year warranty Scope of delivery Pump Optimized Wilo-Connector for all sizes 2x cable gland M16 x 1.5 Washers for flange screws M12 and M16 (for connection nominal widths DN 32 to DN 65) 2x seals for threaded connection Thermal insulation shell Installation and operating instructions (digital) Optional accessories: ClimaForm cold insulation to prevent condensation CIF module: Modbus TCP, Modbus RTU, BACnet IP, BACnet MS/TP, LON, PLR, CANopen Pt1000 (B) pipe clamp sensor (for domestic hot water) Pt1000 (AA) sensor for installation in immersion sleeve Differential pressure sensor Operating data Fluid: Water, ethylene glycol, propylene glycol Min. fluid temperature: -10 °C Max. fluid temperature: 110 °C Min. ambient temperature: -10 °C Max. ambient temperature: 40 °C Maximum operating pressure: 10 bar Minimum inlet head at 50°C: 5 m Minimum inlet head at 95°C: 12 m Minimum inlet head at 110°C: 18 m Motor data Energy efficiency index (EEI): 0.17 Mains connection: 1~230 V ±10%, 50/60 Hz Current (min): 0.2 A Current (max): 2.46 A Rated motor power: 470 W Speed min.: 650 rpm Speed max.: 3350 rpm Power consumption: 10 W Power consumption: 560 W Emission: EN 61800-3;2004+A1;2012 / Residential area (C1) Immunity: EN 61800-3;2004+A1;2012 / Industrial area (C2) Insulation class: F Protection class: IPX4D Cable gland: 5 x M16x1.5 Materials Pump housing: Cast iron Impeller: PPS-GF40 Shaft: 1.4028, DLC-coated Bearings: Carbon, antimony impregnated Installation dimensions Suction-side pipe connection: DN 50 Discharge-side pipe connection: DN 50 Installation length: 280 mm Ordering information Make: Wilo Net weight approx.: 18.8 kg Item number: 2186205