ELTAKO RS485 bus actuator for shading elements and roller shutters – 30014004

Shading element and roller shutter actuator with 2 channels for two 230V motors. 2+2 N/O contacts 4A/250V AC, potential-separated from the 12V supply voltage. Bidirectional. Stand-by loss only 0.1 watt. Series installation device for mounting on DIN-EN 60715 TH35 mounting rail. 1 division unit = 18mm wide, 58mm deep. Connection to the ELTAKO-RS485 bus. Cross-wiring bus and power supply with jumper. Contact switching at zero crossing to protect contacts and motors. One motor is connected to 1, 2 and N, a second motor, if applicable, to 3, 4 and N. If both relays of the FSB14 are switched on, 0.4 watts are required. In case of supply voltage failure, it switches off in a defined manner. The pushbuttons can be taught-in either as directional pushbuttons or as universal pushbuttons: Local control with universal pushbutton: With each button press, the switching position changes in the sequence Up, Stop, Down, Stop. Local control with directional pushbutton: With a button press up, the "Up" switching position is specifically activated. With a button press down, the "Down" switching position is specifically activated. Another button press in the same direction immediately interrupts the process. However, a button press in the other direction stops and, after a 500ms pause, switches to the opposite direction of travel. Dynamic central control without priority: With a control signal from a pushbutton taught-in as a central control pushbutton without priority, the switching position Up or Down is specifically activated. Without priority because this function can be overridden by other control signals. Dynamic central control with priority: With a control signal of at least 2 seconds from a pushbutton taught-in as a central control pushbutton with priority, the switching position Up and Down is specifically activated. With priority because these control signals cannot be overridden by other control signals until the central command is cancelled by an Up or Down button press from the central control pushbutton. With a control signal, e.g. from an FSM61 taught-in as a central control pushbutton with priority, the switching position Up or Down and the priority are specifically activated. With priority because these control signals cannot be overridden by other control signals until the central command is cancelled by the end of the control signal. Shading scene control: With a control signal from a pushbutton taught-in as a scene pushbutton with a double rocker switch or automatically by an additionally taught-in wireless outdoor brightness sensor, up to 4 previously stored run-down times can be recalled. When controlled via a controller, travel commands for Up and Down can be started with the exact travel time specification. Since the actuator reports the exact travel time after each activity, even when driving triggered by a pushbutton, the position of the shading is always displayed correctly in an app. When the upper and lower end positions are reached, the position is automatically synchronized. Function rotary switch at the bottom: AUTO 1 = In this position of the rotary switch, the comfort turning function for blinds is switched on. When controlled with a universal pushbutton or a directional pushbutton, a double impulse causes slow turning in the opposite direction, which is stopped with another impulse. AUTO 2 = In this position of the rotary switch, the comfort turning function for blinds is completely switched off. AUTO 3 = In this position of the rotary switch, the local pushbuttons initially act statically, thus allowing blinds to be turned by tapping. Only after 0.7 seconds of continuous activation do they switch to dynamic. AUTO 4 = In this position of the rotary switch, the local pushbuttons only act statically (ER function). The fallback delay RV (wiping time) of the upper rotary switch is active. Central control is not possible. Arrow up/arrow down = Manual control is performed in the arrow up (Up) and arrow down (Down) positions of the lower rotary switch. Manual control has priority over all other control commands. WA = The automatic turning function for blinds and awnings is set with the middle rotary switch. 0 = off, otherwise switched on between 0.3 and 5 seconds with the set turning time. In this case, a change of direction is only made when moving down after the delay time set with the upper rotary switch has elapsed, for example, to tension awnings or to set blinds to a specific position. Below the RV rotary switch is the LED display for the turning time. RV = The delay time (fallback delay RV) is set with the upper rotary switch. If the FSB14 is in the Up or Down position, the set delay time runs, at the end of which the device automatically switches to Stop. The delay time must therefore be chosen to be at least as long as the shading element or roller shutter needs to move from one end position to the other. Below the RV rotary switch is the LED display for the RV delay time. If one or more wireless window/door contacts FTK or window handle sensor FFG7B are taught-in, an lockout protection is set up when the door is open, which blocks a central Down command. The LED below the upper rotary switch accompanies the teaching-in process according to the operating instructions and indicates control commands by short flashing during operation.