WILO Wilo Smart Pump Stratos MAXO 30/0.5-10 PN10 (DE) – 2186191

Premium Smart-Pump Wilo-Stratos MAXOHigh-efficiency in-line wet rotor pump with EC motor and electronic power control. Can be used for heating water, chilled water, and water-glycol mixtures. Energy efficiency index (EEI) between ≤ 0.17 and ≤ 0.19, depending on the pump type.Control modes:Permanent, automatic power adjustment to system requirements without setpoint specification Wilo-Dynamic Adapt plus (factory setting). Up to 20% energy saving compared to dp-v control mode.Constant temperature (T-const.)Constant differential temperature (dT-const.)Demand-driven flow optimization of the booster pump through networking and communication with multiple pumps (Multi-Flow Adaptation).Constant flow rate (Q-const.)Differential pressure control dp-c at a remote point in the piping network (worst-point control)Constant differential pressure (dp-c)Variable differential pressure (dp-v) with the option of nominal operating point inputConstant speed (n-const.)User-defined PID controlFunctions:Heat quantity measurementCooling quantity measurementAutomatic pump shutdown upon zero-flow detection (No-Flow Stop)Switching between heating and cooling mode (automatic, external, or manual)Adjustable flow rate limitation through Q-Limit function (Qmin. and Qmax.)Dual pump operating modes: Efficiency-optimized additive operation for dp-c and dp-v, main/standby operationSave and restore configured pump settings (3 restore points)Plain text error/warning message display including remedy recommendationDeaeration function for automatic deaeration of the rotor chamberAutomatic night setbackAutomatic deblocking function and integrated full motor protectionDry-running detectionDisplay:Control modeSetpointFlow rateTemperaturePower consumptionElectrical consumptionActive influences (e.g., STOP, No-Flow Stop)Design:2 configurable analog inputs: 0-10 V, 2-10 V, 0-20 mA, 4-20 mA and commercially available Pt1000; power supply with +24 V DC2 configurable digital inputs (Ext. OFF, Ext. Min, Ext. Max, Heating/Cooling, Manual override (BMS decoupled), Operating lock (keypad lock and remote control configuration protection))2 configurable alarm relays for operating and fault messagesSlot for Wilo-CIF modules with interfaces for building automation GA (Optional accessories: CIF modules Modbus RTU, Modbus TCP, BACnet MS/TP, BACnet IP, LON, PLR, CANopen)Wilo Net as Wilo system bus for communication between Wilo products, e.g., Multi-Flow Adaptation; dual pump operation and Wilo-Smart GatewayIntegrated temperature sensorAutomatic emergency operation in special conditions (pump speed definable) e.g., in case of bus communication failure or sensor valuesGraphically colored display (4.3 inches) with one-button manual controlRead out and set operating data, e.g., create a commissioning protocol via Bluetooth interface (without additional accessories) using the Wilo Assistant AppDual pump management integrated (dual pumps are pre-wired), when using 2 single pumps as a dual pump unit, connection via WILO NetCable break detection for analog signal (in conjunction with 2-10 V or 4-20 mA)Outdoor installation with weather protection possible according to installation and operating instructionsDate and time presetThermal insulation shell for heating applications5-year warrantyScope of deliveryPumpOptimized Wilo-Connector for all sizes, identical2x cable gland M16 x 1.5Washers for flange screws M12 and M16 (for connection nominal widths DN 32 to DN 65)2x gaskets for threaded connectionThermal insulation shellInstallation and operating instructions (digital)Optional accessories:ClimaForm cold insulation to prevent condensationCIF module: Modbus TCP, Modbus RTU, BACnet IP, BACnet MS/TP, LON, PLR, CANopenPt1000 (B) pipe clamp sensor (for domestic hot water)Pt1000 (AA) sensor for installation in immersion sleeveDifferential pressure sensorOperating dataFluid: Water, ethylene glycol, propylene glycolMin. fluid temperature: -10 °CMax. fluid temperature: 110 °CMin. ambient temperature: -10 °CMax. ambient temperature: 40 °CMaximum operating pressure: 10 barMinimum inlet pressure at 50°C: 3 mMinimum inlet pressure at 95°C: 10 mMinimum inlet pressure at 110°C: 16 mMotor dataEnergy efficiency index (EEI): 0.19Mains connection: 1~230 V ±10%, 50/60 HzCurrent (min): 0.11 ACurrent (max): 1.2 AMotor rated power: 234 WSpeed min.: 750 rpmSpeed max.: 3950 rpmPower consumption: 7 WPower consumption: 275 WEmitted interference: EN 61800-3;2004+A1;2012 / Residential area (C1)Immunity to interference: EN 61800-3;2004+A1;2012 / Industrial area (C2)Insulation class: FProtection class: IPX4DCable gland: 5 x M16x1.5MaterialsPump housing: Cast ironImpeller: PPS-GF40Shaft: 1.4122, DLC-coatedBearing: Carbon, antimony-impregnatedInstallation dimensionsSuction pipe connection: G 2Discharge pipe connection: G 2Installation length: 180 mmOrdering informationBrand: WiloNet weight approx.: 7.5 kgArticle number: 2186191